Questo argomento contiene 1 risposta, ha 2 partecipanti, ed è stato aggiornato da Nic D’Ercole 2 anni, 8 mesi fa.
-
AutoreArticoli
-
21 Giugno 2016 alle 10:02 #397
Anonimo“Problema avvio Endian UTM Mini”
Allego tutta la procedura di boot che compare collegandomi tramite la porta “console”U-Boot 2009.08-rc1-00039-gb30fcb0 (Aug 26 2009 – 07:59:58)
Marvell-Sheevaplug
SoC: Kirkwood 88F6281_A0
DRAM: 512 MB
NAND: 512 MiB
Net: egiga0
PHY reset timed out
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x300000
3145728 bytes read: OK
(Re)start USB…
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices… 2 USB Device(s) found
scanning bus for storage devices… 1 Storage Device(s) found
## Booting kernel from Legacy Image at 06400000 …
Image Name: Linux-2.6.32.43-57.e51.armv5tel
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2208696 Bytes = 2.1 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum … OK
Loading Kernel Image … OK
OKStarting kernel …
Uncompressing Linux………………………………………………………………………………………………………………………….. done, booting the kernel.
[ 0.000000] Linux version 2.6.32.43-57.e51.armv5tel (root@bs-arm-01) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-13)) #1 Wed Mar 19 08:57:59 EDT 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Marvell SheevaPlug Reference Board
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:512k(uboot),3m@1m(kernel),1m@4m(psm),13m@5m(rootfs) rw root=/dev/mtdblock3 rw rootfstype=jffs2
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 256MB 256MB = 512MB total
[ 0.000000] Memory: 514944KB available (3960K code, 379K data, 120K init, 0K highmem)
[ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is enabled.
[ 0.000000] NR_IRQS:114
[ 0.000044] Calibrating delay loop… 1192.75 BogoMIPS (lpj=5963776)
[ 0.240250] Security Framework initialized
[ 0.240269] SELinux: Initializing.
[ 0.240355] Mount-cache hash table entries: 512
[ 0.241385] CPU: Testing write buffer coherency: ok
[ 0.246772] NET: Registered protocol family 16
[ 0.249569] Kirkwood: MV88F6281-A1, TCLK=200000000.
[ 0.249581] Feroceon L2: Cache support initialised.
[ 0.285375] bio: create slab <bio-0> at 0
[ 0.286636] vgaarb: loaded
[ 0.288716] SCSI subsystem initialized
[ 0.293079] usbcore: registered new interface driver usbfs
[ 0.293845] usbcore: registered new interface driver hub
[ 0.294297] usbcore: registered new device driver usb
[ 0.298711] NetLabel: Initializing
[ 0.298721] NetLabel: domain hash size = 128
[ 0.298727] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.299133] NetLabel: unlabeled traffic allowed by default
[ 0.299175] Switching to clocksource orion_clocksource
[ 0.303556] NET: Registered protocol family 2
[ 0.303941] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.305196] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.305550] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.305752] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.305761] TCP reno registered
[ 0.306200] NET: Registered protocol family 1
[ 0.312270] audit: initializing netlink socket (disabled)
[ 0.312361] type=2000 audit(0.290:1): initialized
[ 0.383311] msgmni has been set to 1006
[ 0.386706] alg: No test for stdrng (krng)
[ 0.387742] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.387756] io scheduler noop registered
[ 0.387763] io scheduler anticipatory registered
[ 0.387770] io scheduler deadline registered
[ 0.388848] io scheduler cfq registered (default)
[ 0.664740] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.668733] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 0.964355] console [ttyS0] enabled
[ 0.987378] brd: module loaded
[ 0.990915] Uniform Multi-Platform E-IDE driver
[ 0.997656] ide-gd driver 1.18
[ 1.006009] impA7:probing 0x00800000 at 0x00000000
[ 1.011257] impA7:probing 0x00800000 at 0x10000000
[ 1.016697] GPIO NAND driver, © 2004 Simtec Electronics
[ 1.023115] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit)
[ 1.031969] Scanning device for bad blocks
[ 1.110000] Bad eraseblock 1993 at 0x00000f920000
[ 1.134852] Bad eraseblock 2536 at 0x000013d00000
[ 1.197380] 4 cmdlinepart partitions found on MTD device orion_nand
[ 1.203688] Creating 4 MTD partitions on “orion_nand”:
[ 1.208859] 0x000000000000-0x000000080000 : “uboot”
[ 1.216073] 0x000000100000-0x000000400000 : “kernel”
[ 1.223129] 0x000000400000-0x000000500000 : “psm”
[ 1.229821] 0x000000500000-0x000001200000 : “rootfs”
[ 1.242064] MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.248183] mv643xx_eth smi: probed
[ 1.254225] net eth0: port 0 with MAC address 00:00:00:00:00:00
[ 1.261982] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 1.268631] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 1.274857] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 1.309258] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 1.329210] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 1.335423] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.342264] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.349528] usb usb1: Product: Marvell Orion EHCI
[ 1.354254] usb usb1: Manufacturer: Linux 2.6.32.43-57.e51.armv5tel ehci_hcd
[ 1.361342] usb usb1: SerialNumber: orion-ehci.0
[ 1.366810] usb usb1: configuration #1 chosen from 1 choice
[ 1.372950] hub 1-0:1.0: USB hub found
[ 1.376779] hub 1-0:1.0: 1 port detected
[ 1.382235] Initializing USB Mass Storage driver…
[ 1.387569] usbcore: registered new interface driver usb-storage
[ 1.393684] USB Mass Storage support registered.
[ 1.398773] usbcore: registered new interface driver libusual
[ 1.405105] usbcore: registered new interface driver ums-datafab
[ 1.411580] usbcore: registered new interface driver ums-freecom
[ 1.417975] usbcore: registered new interface driver ums-jumpshot
[ 1.424573] usbcore: registered new interface driver ums-sddr09
[ 1.430997] usbcore: registered new interface driver ums-sddr55
[ 1.437479] mice: PS/2 mouse device common for all mice
[ 1.443545] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 1.450485] Orion Watchdog Timer: Initial timeout 21 sec
[ 1.456896] cpuidle: using governor ladder
[ 1.462552] cpuidle: using governor menu
[ 1.467462] mmc0: mvsdio driver initialized, lacking card detect (fall back to polling)
[ 1.476976] Registered led device: plug:green:health
[ 1.482697] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 1.489115] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 1.529525] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 1.569472] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 1.582029] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 1.590252] mmc0: new high speed SDHC card at address 0007
[ 1.597144] mmcblk0: mmc0:0007 SD8GB 7.42 GiB
[ 1.601843] mmcblk0: detected capacity change from 0 to 7969177600
[ 1.608214] mmcblk0:
[ 1.610773] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 1.620043] p1
[ 1.649474] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 1.667000] usbcore: registered new interface driver hiddev
[ 1.673391] usbcore: registered new interface driver usbhid
[ 1.678995] usbhid: v2.6:USB HID core driver
[ 1.683902] oprofile: using timer interrupt.
[ 1.690703] TCP cubic registered
[ 1.693949] Initializing XFRM netlink socket
[ 1.698278] NET: Registered protocol family 17
[ 1.703212] usb 1-1: new high speed USB device using orion-ehci and address 2
[ 1.710778] VFP support v0.3: not present
[ 1.716631] registered taskstats version 1
[ 1.721950] rtc-mv rtc-mv: setting system clock to 2092-12-16 02:33:34 UTC (3880233214)
[ 1.731840] VFS: Cannot open root device “mtdblock3” or unknown-block(31,3)
[ 1.738832] Please append a correct “root=” boot option; here are the available partitions:
[ 1.747308] 1f00 512 mtdblock0 (driver?)
[ 1.752317] 1f01 3072 mtdblock1 (driver?)
[ 1.757312] 1f02 1024 mtdblock2 (driver?)
[ 1.762318] 1f03 13312 mtdblock3 (driver?)
[ 1.767314] b300 7782400 mmcblk0 driver: mmcblk
[ 1.772599] b301 7781376 mmcblk0p1
[ 1.776897] Kernel panic – not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
[ 11.739192] INFO: RCU detected CPU 0 stall (t=1000 jiffies)
[ 41.739191] INFO: RCU detected CPU 0 stall (t=4000 jiffies)
[ 71.739190] INFO: RCU detected CPU 0 stall (t=7000 jiffies)
[ 101.739190] INFO: RCU detected CPU 0 stall (t=10000 jiffies)
[ 131.739190] INFO: RCU detected CPU 0 stall (t=13000 jiffies)
[ 161.739190] INFO: RCU detected CPU 0 stall (t=16000 jiffies)
[ 191.739190] INFO: RCU detected CPU 0 stall (t=19000 jiffies)
[ 221.739190] INFO: RCU detected CPU 0 stall (t=22000 jiffies)
[ 251.739190] INFO: RCU detected CPU 0 stall (t=25000 jiffies)
[ 281.739190] INFO: RCU detected CPU 0 stall (t=28000 jiffies)
[ 311.739190] INFO: RCU detected CPU 0 stall (t=31000 jiffies)
[ 341.739190] INFO: RCU detected CPU 0 stall (t=34000 jiffies)
[ 371.739190] INFO: RCU detected CPU 0 stall (t=37000 jiffies)
[ 401.739190] INFO: RCU detected CPU 0 stall (t=40000 jiffies)
[ 431.739190] INFO: RCU detected CPU 0 stall (t=43000 jiffies)
—————————————————————————-Così ho pensato di utilizzare il tool “MiniRepairTool-1.3.exe”
“Mini Repair tool – Mini ARM NAND Recovery” da l’errore “Error: Hardware revision not affected. Fix not applied.”
quindi ho provato ad utilizzare il tool “Disaster Recovery” dopo de fare tutti i passaggi indicati sul sito endian.comdopo l’ultimo comando “run bootrecovery”
si ferma con la scritta:
Starting kernel …
Uncompressing Linux………………………………………………………………………………………………………………………….. done, booting the kernel.
Qualcuno sa darmi una mano?
21 Giugno 2016 alle 14:37 #398Ciao Julio,
per la versione non community forse ti dovresti rivolgere all’assistenza endian e non qui sui forum community.
Ciao
-
AutoreArticoli
Devi essere loggato per rispondere a questa discussione.